What’s new on the B2B Market?
Apr 28 2019
Date: April 28, 2019 10:00 PM
Precisely, and thanks to Electricfor's long experience in the renewable energy sector, it has been possible to carry out this project whose main objective is to test the electric charger with an electric charge station in a laboratory.
WHAT IS A CHARGING STATION?
A charging station is a unit incorporating an internal alignment of shielded electrical elements with a built-in fan to air them and remove the internal heat produced inside.
This charging station is powered by 180 kW and the heating elements inside can work under a voltage of 1,000Vdc.
It is therefore a very interesting project that shows, once again, Electricfor's commitment to renewable energy, and with the boom in the production and launch of new electric cars.
For further information about this project and the equipment that is part of these charging stations, you can consult with Electricfor's sales department.
Apr 28 2019
Date: April 28, 2019 10:00 PM
A new generation of AGVs from the Austrian company AGILOX Services GmbH is revolutionising logistics: The Intelligent Guided Vehicle (IGV) AGILOX is an agile, autonomous plug & play transport system that has achieved international success with new concepts for spatial navigation and swarm intelligence. Such high-tech transport systems create tremendous advantages in logistics, because they save space and reduce personnel costs. Reliable prevention of collisions between people and objects, however, requires cutting-edge, certified sensor technologies.
Little space for advanced technology
An especially challenging task in this development was to protect the blind zone of the IGV AGILOX from the fork arms in the phase immediately prior to entering the pallet. Since the installation space for sensors in this area is very small, It was difficult to find suitable sensors. In the end, the Austrian sales partner Urmet Dialog pointed AGILOX Services toward the USi® ultrasonic sensors from Mayser GmbH & Co. KG. Domiciled in Ulm and Lindenberg, the company manufactures products and system solutions for safety technology, foam technology and moulded components at six locations in Europe, Asia and the USA.
Complex echo process ensures reliable object detection
Mayser developed its USi® ultrasonic sensors especially for non-touch monitoring of three-dimensional spaces. A complex process consisting of an echo propagation time measurement and an echo amplitude measurement allows both distance measurements and non-touch object detection by the sensor. The USi® detects objects made of diverse materials and is insensitive to contamination, extraneous sound, air flows and moisture. It also features very compact, freely positionable transducers that can be positioned apart from the electronic system for increased versatility of installation – even in very tight spaces. A special new software routine provides for added safety by suppressing mutual interference if two independent transport systems meet each other.
High safety standards
Since the areas of application for the IGV AGILOX also include work areas where people move about, the USi® Safety with a special dual channel system for personnel safety was added during the course of the cooperation. AGILOX Services therefore received a technology that was even more innovative and more complex than the original requirement. Equipped with USi® and USi® Safety at the end of the integration process, the Intelligent Guided Vehicle from AGILOX Services can now operate without interruptions, which allows maximum efficiency. In addition, the IGV AGILOX is the only automated transport system on the market that is fully protected according to ISO 13849-1 Category 3 PL d – a unique selling proposition with long-term benefits for AGILOX Services.
“The use of USi® Safety in very small installation spaces has allowed us to make the AGILOX altogether more safe, while keeping everything very smart.”
Josef Baumann-Rott, Co-founder AGILOX Services GmbH
As a manufacturer and supplier of plastic components such as energy chains, cables and bearings, igus is also going through a digital development process and is increasingly orienting its products towards use in smart factories. The aim is to make the maintenance and repair of its plastics more efficient and cost-effective. Thanks to the newly developed isense products from igus, maintenance and repair are not only being focused on more intensively in industrial production; they also profit from digitisation and its advantages as do all other areas of production.
Apr 23 2019
Date: April 23, 2019 3:00 PM
All the 81 enterprises participated in the 21st Export Consultation Meeting with World Congress of Representatives which is held on 24th of April, 2019, in Jeongsun, Gangwondo.
Raphadeo signed a million-dollar export contracts with ‘Viva World’, which is Austrailian Trade company.
Today, a total 81 companies, including 45 Gangwon-do Excellent Companies, 10 companies belonging to the Korea Fisheries Association and 26 companies participating in World OKTA-associated overseas branching project took part in this Export Consultation Meeting and had business meetings with Korean Buyers who are members of World OKTA.
They sought opportunities to enter foreign markets by consulting with at least six to seven Korean buyers and as many as nine to ten Korean buyers.
Apr 21 2019
Date: April 21, 2019 10:00 PM
- Payload up to 30N
- Cycle times > 6s
- Reach up to 790mm
- Also available as DPI version with integrated control system
- With motor encoders upon request
- Version with drive encoders possible
- Available as 4 DOF or 5 DOF (degrees of freedom)
- Optimised bearing support of the single axes for less
Apr 17 2019
Date: April 17, 2019 10:00 PM
Typical application areas: applications with large unsupported lengths, high fill weights and long travels
The machines that the customer is interested in are including 1325 ATC CNC router with auto loading , automatic edge banding machine, side drilling machine, wood sanding machine, vacuum laminating machine and others.
One of the things worth mentioning is our fully automatic loading and unloading panel furniture production line. The following advantages make it very popular in the furniture processing industry.
- Bed structure: The structure of the machine is exquisite, achieving a win-win of speed and precision.
- Save time: With self-contained pusher device, it’s convenient for operators to take materials, saving time. It also has dual-station equipment, which can be used to maximize production efficiency.
- Vacuum table: With the vacuum adsorption table, it can process different shapes of plates.
- Saving labor: The automatic loading and unloading, vertical punching, rectangular cutting, profile cutting and grooving operations can be completed at the same time, which can save labor cost by about 60%.
- High efficiency: The processed sheet does not collapse, and 60-80 sheets can be completed in one day.
- Other combinations: Drilling and automatic tool change combination, can achieve drilling, pulling and other functions.
Our commitment to Lean manufacturing drives waste out of every phase of the sales and manufacturing process. That means you get the best quality products with shorter lead times at more competitive prices—from worldwide material procurement to inventory management and delivery. Plus, you can rely on us for 100% defect-free parts guaranteed because all of our hinges are manufactured using our Total Quality Management (TQM) program.
Apr 14 2019
Date: April 14, 2019 3:00 PM
Location: Guangzhou City, China
Canton Fair(China Import and Export Fair) is the largest trade fair with the largest scale, the most complete exhibit variety, the broadest distribution of overseas buyers and the greatest business turnover held in Guangzhou Canton China.
IDM Corp. participated in CANTON FAIR of Phase 1
Apr 12 2019
Date: April 12, 2019 10:20 AM
The extensive Elesa system of mounting clamps, rods and tubes is quality engineered to enable location of devices often suspended somewhat in space – by providing a supporting framework. The range is modular in design which makes selection simple – so rods/tubes can readily be matched with connecting clamps with/without base or flanges to ensure solid mounting on floors or structural elements. Linear connecting rods, actuating gears, angle clamps, clamp handles and two-way connecting clamps comprise a full system of standard mounting components.
Further information regarding Elesa mounting clamps, rods and tubes may be found at: www.elesa.com/en/elesab2bstoreuk/catalogo-cat-166-sales/connecting-clamps--1 or follow them on twitter: www.twitter.com/ElesaUK.
Education, best-practices sharing, networking, discovery of new skills and approaches, and the latest news in the world of international trade policies and practices are all part of the takeaways from the NASBITE International Annual Conference.
Apr 3 2019
Date: April 3, 2019 10:00 PM
Tecnova Piscinas, Siga and Genera, in which Electricfor was also present, were also held simultaneously with Climatización y Refrigeración.
WHAT IS CLIMATIZACIÓN Y REFRIGERACIÓN?
C&R is an international show where the most advanced air conditioning market solutions are presented, and an overview of the industry is provided through novelties introduced by more than 375 companies. These novelties include innovation in related technology, optimisation and installation control, equipment design, new refrigerants, energy cost reduction and environmental care.
On the other hand, Genera is the international trade fair for energy and the environment; while Tecnova Piscinas and Siga are closely related to technology and innovation in swimming pools and water management.
The primary objective of all these shows is to capture the attention and interest of its participants in technological innovation, energy efficiency and the environment.
ELECTRICFOR PRODUCT APPLICATIONS
Electricfor's main product is used at all the fairs mentioned above, which, as we have already said, have featured its presence:
- At Climatización y Refrigeración, air-water heating and defrosting.
- At Tecnova Piscinas, water heating.
- At Siga, water heating.
- At Genera, air, gas and water heating. Engineering related applications as well.
For further information and details about Electricfor products and applications, please contact its sales department.
Apr 3 2019
Date: April 3, 2019 3:00 PM
Leinfelden-Echterdingen, Germany, April 02, 2019 - Creaform, a world leader in automated and portable 3D metrology solutions, will be showcasing portable 3D scanners to measure the shape and geometry of castings at GIFA 2019 (Hall 13, Booth B35), which will take place from June 23 to 25, 2019 in
Creaform’s portable 3D scanners enable quality control teams to perform inspections during the design or production process. The scanners help to avoid unnecessary, repetitive construction steps and ensure that castings perfectly match CAD references. For example, before machining, raw castings must be checked to see if machining is possible. This way, teams can determine if there is enough material on the casting or remove extra material, if necessary. After machining, the dimensional accuracy of the final castings must be checked to see if they correspond to the CAD. Ideally, 3D scanning systems are used for these tasks.
The HandySCAN 3D and the MetraSCAN 3D—both developed by Creaform—quickly and accurately capture the dimensions of every imaginable shape, even under the harshest production environments.
The HandySCAN 3D is a metrology-grade handheld portable 3D laser scanner. It is the fastest on the market and features the highest measurement rate and accuracy available –all while remaining very simple to use. Its self-positioning capabilities and portability provide unmatched freedom of movement. It is the perfect solution when confined areas need to be reached or smaller parts ranging from 0.1 to 4 m in size have to be measured, regardless of their complexity, material, or color. The HandySCAN 3D provides consistent and repeatable results across all work conditions or environments, enabling you to reduce turnaround times and increase profitability.
The MetraSCAN 3D is the most complete 3D scanning solution for metrology-grade measurements and inspections. Truly portable and insensitive to changes found in shop-floor environments (e.g. vibrations, part displacements, setups and CMM instability), it significantly increases the reliability, speed and versatility of 3D measurement processes. It also outperforms scanners that are mounted on traditional portable CMMs. The MetraSCAN 3D is the best solution for geometrical and freeform surface inspections on parts ranging from 0.2 to 10 m in size, regardless of their type of material, color, or reflectivity. Paired with the C-Track optical tracker that enables dynamic referencing, automatic alignment and continuous monitoring of parameters, it provides the most accurate measurements in the lab and on the shop floor. Offering optional probing capabilities with the HandyPROBE Next, users can harness the power of both 3D scanning and portable optical CMMs for a streamlined inspection process.
Creaform scanners are universally applicable, allow for very fast and simple data acquisition as well as very accurate measurements and quality control even under the most difficult conditions directly on production lines. The recorded data is exported as STL models so that a CAD comparison with a reference part can be made directly after measurement. As a result, the main causes of casting quality issues can be quickly identified and addressed, thereby avoiding costly bottlenecks during large-series production runs and major product recalls.
Apr 1 2019
Date: April 1, 2019 10:00 PM
The CA 1860 & CA 1862 no‐contact thermometers from Chauvin Arnoux are simple and accurate. Ergonomic, lightweight, easy‐to‐handle, rugged and watertight (IP 65), they offer a large number of measuring functions, including parameterizable alarm thresholds.
Ergonomics designed for simplified use
The CA 1860 and CA 1862 are pistol‐shaped with a trigger for comfortable handling. Weighing in at less than 300 g, they are also very rugged: they withstand falls from up to 3 m!
For all‐terrain use, they offer IP65 ingress protection. The measurement results are displayed on the backlit LCD screen.
They are delivered in a carrying bag.
Functions and measurements
Dedicated to remote temperature measurement, these new infrared thermometers offer excellent metrological performance.
The laser sight enables you to target a zone precisely. The CA 1862 is equipped with a dual laser sight for even more precise targeting.
With their broad measurement range and numerous functions, the CA 1860 and CA 1862 facilitate users' work.
Measurement is performed simply by pressing the trigger. The trigger can also be locked for continuous measurements. Multiple measurement modes are available, enabling you to obtain instantaneous, averaged and differential values, or simply the Min and Max values.
The high and low alarm thresholds can be parameterized directly by the user and are indicated by the "HI" and "LO" LEDs located just above the display.
The CA 1860 offers fixed emissivity, while the emissivity of the CA 1862 can be adjusted from 0.1 to 1.
Apr 1 2019
Date: April 1, 2019 9:00 PM
Powerful drives, high power density and easy integration — these keywords best describe this year's presence at the world's largest technology trade show in Hanover from April 1st – 5th. maxon motor will present new solutions that will benefit customers all over the world.
Special attention should be paid to the new IDX line, a modular drive system for applications in industrial automation or logistics automation that consists of a motor and an integrated EPOS4 controller that can be used in a wide variety of applications. The IDX compact drives will be configurable online.... read more